A compression type mid-span joint consists of the following parts:a. Aluminium alloy tube for aluminium alloy conductors.b.
Contact Now
The preformed strain clamp is used to bear full tension on the bare conductors and overhead insulated conductors in the power transmission and distribution line, and connect the conductors to the strain tower, which can replace the conventional bolt-type strain clamp and compression type strain Clamps and wedge-shaped strain clamps.Structure composition and material description 1. Non-twisted ring: standard form, suitable for small diameter wires; Stranded ring: suitable for larger diameter wires 2. Color code: starting mark of installation 3. Label: Indicate the
Contact Now
Material 1. Rubber Clamps Composed of high-quality rubber and center reinforcement, it has the properties of ozone resistance, chemical resistance, weather resistance, high and low temperature performance, high strength and elasticity, and small compression deformation. 2. Aluminum splint It is made of corrosion-resistant aluminum alloy by pressure casting. The aluminum alloy has stable chemical properties, good atmospheric corrosion resistance and good mechanical properties.
Contact Now
ADSS optical cable suspension clamp components: 1.Aluminum clamp:made of corrosion-resistant aluminum alloy pressure casting, the aluminum alloy has stable chemical properties, good atmospheric corrosion resistance and good mechanical properties. 2.Rubber clamp:Composed of high-quality rubber and center reinforcement, it has the properties of ozone resistance, chemical resistance, weather resistance, high and low temperature performance, high strength and elasticity, and small compression deformation. 3.Bolts, flat washers, spring washers, nuts, closed pins, U-shaped hanging rin
Contact Now
Features: 1. The application force has no concentrated point, the stress is uniform, and it has a good protective effect on the optical cable. 2. Under the premise of not exceeding the lateral compression strength of the optical cable, it has a greater grip on the optical cable and can withstand greater tension.
Contact Now
The preformed strain clamp is used to undergo full anxiety on the naked conductors and overhead insulated conductors in the energy transmission and distribution line, and connect the conductors to the stress tower, that could replace the traditional bolt-type stress clamp and compression kind strain clamps and wedge-shaped stress clamps.Structure composition and material description 1. Non-twisted ring: standard form, suitable for small diameter wires; Stranded ring: suitable for larger diameter wires 2. Color code: starting mark of installation 3. Label: Indicate the produ
Contact Now
CAPG copper-aluminum special-shaped parallel clamp is suitable for the non-load-bearing splicing and branching of aluminum stranded wire, steel core aluminum stranded wire and copper branch wire. Through the re-processing of the profile, the aluminum density is better after the second forging, and the strength of the wire clip is improved. higher. There is a layer of blue epoxy resin on the inside of the wire clip to better isolate the air from the copper-aluminum welding joint and prevent the electrochemical corrosion of the copper-aluminum.
Contact Now
Features: a. Even stress distribution, no stress concentration point, can well protect the optical cable. b. Under the premise of not exceeding the lateral compression strength of the optical cable, it has a greater grip on the optical cable and can withstand greater tension. c. The grip strength of the optical cable is not less than: 95% of the ultimate tensile strength (UTS) of the optical cable, which is fully suitable for the needs of optical cable erectionProduct composition diagramProduct technical specification sheet: Sn Model No.
Contact Now
OPGW Optical Cable Tension Fitting StringFeatures:a. Even stress distribution, no stress concentration point, can well protect the optical cable.b. Under the premise of not exceeding the lateral compression strength of the optical cable, it has a greater grip on the optical cable and can withstand greater tension.c. The grip strength of the optical cable is not less than: 95% of the ultimate tensile strength (UTS) of the optical cable, which is completely suitable for the needs of optical cable erection. Schematic diagram of product composition:Technical specification sheet
Contact Now
The preformed tension clamp for the conductor is connected to the tower by its matching fittings, such as insert ring, bowl-head hanging plate, etc., which can replace conventional bolt-type tension clamps, compression-type tension clamps and wedge-type tension cables folder.Structure composition and material description 1. Non-twisted ring: standard form, suitable for small diameter wires; Stranded ring: suitable for larger diameter wires 2. Color code: starting mark of installation 3. Label: Indicate the product model 4. Pre-twisted wire: aluminum-clad stee
Contact Now
The preformed helical guy grip clamp for the conductor is hooked up to the tower by means of its matching fittings, along with insert ring, bowl-head striking plate, and so forth., that could replace conventional bolt-type tension clamps, compression-type anxiety clamps and wedge-type anxiety cables folder.Structure composition and material description 1. Non-twisted ring: standard form, suitable for small diameter wires; Stranded ring: suitable for larger diameter wires 2. Color code: starting mark of installation 3. Label: Indicate the product model 4. Pre-twisted wi
Contact Now
The U shackle is made of forged steel, has a wide range of uses.
Contact Now
Retention Clamp for ADSS cable single extension 50M span cable diameter 9.0-9.5mmTension splint for ADSS tower is made of forged hot dip galvanized steel.use: for installation and maintenance of aerial construction fiber optic networks.Technical Characteristics1. Fitting material: Steel under ASTM A-362. Minimum yield strength: 250Mpa.3. Minimum tensile strength: 400Mpa4. Post fastening method: By 3/4” steel tape.5. Solder points with smooth and uniform finishes6. Hot dip galvanized according to ASTM A 123 Dimensions1. Fitting base dimensions:
Contact Now
Steel belt 20X0.7mm with buckle, tts strength and ductility meet requirements for bending the different size of cables on poles. Steel Buckle can hold a single or double wrapped band configuration.Packing:Steel roll of 50 m is packed in form of closed reel rewind tape in nylon plastic roll.
Contact Now
The down-lead clamp for metal rods is used to fix ADSS on the rod. It is suitable for different cable diameters. It is convenient and reliable to install and has a wide adjustable range.1.Function: Fix the optical cable leading up or down on the pole tower to prevent it from shaking and avoid the optical cable from wearing. 2.Condition: The fiber optic cable line and the continuous poles on the first and end poles. 3.Method: usually install one every 1.5 meters.Technical specification table:
Contact Now
NLL wedge-shaped tension clamp body is made of high-strength aluminum alloy; the outer shell is smooth and has a long service life; it is easy to install and use; it has no power loss and is an energy-saving certified product.Features:1. Model : wedge type2. Material: high strength alloy aluminum3. Model No.: NLL-34. U bolt number: 3 nos5. Tension strength: 60kN Technical specification: Model1KV Overhead Insulated wire10KV Overhead Insulated wireWire clamping rangeφ (mm)U-boltNominal failure loadNumberdiameterNLL-125~7010~255.0~10.02M1240NLL-250~120
Contact Now
The self-supporting figure 8 optical cable clamp has a flat surface, special material and embedded design, which can well protect the cable. Its technology is superb: high-quality aluminum alloy material, rubber clamp block, reduce wear.
Contact Now
U type bow shackle mostly used for the ADSS cable installation, which be compatible with tension screws. There are M12 or M14 two types for 40kN shackles, and all will be hot dip galvanized steel.Model No.: U-4Bolt size: M12& M14Drawing: Installation image(part 4) :
Contact Now
FTTH drop cable fisher screw eye is installed on the bracket, used to connect and fix the S fixing piece. The expansion plug is used in conjunction with the ring hook. It is used as an optical fiber access accessory on the cement wall.
Contact Now
FTTH drop cable screw eye is a supporting device that is directly screwed to a wooden wall or fixed to a brick-concrete wall with an expansion tube to connect and fix the S fixing member. Cement walls need to be used with expansion plugs.The expansion plug is used in conjunction with the ring hook. It is used as an optical fiber access accessory on the cement wall.
Contact Now
The PA2000 FTTH plastic tension clamp is designed to anchor insulated service lines with 2 conductors to the pole. The clamp is composed of a body, wedges and removable, adjustable bail. One core adjustable anchor clamp are designed to supporting the neutral messenger, the wedge can be self-adjusted.Features:Unit weight:550gCarton size: 550×410×250mmQuantity per carton : 50 piecesMaterial: Nylon and stainless steelCable diameter: 12-15mmTension strength: 7KNDrawing:
Contact Now
APG-A1 Aluminum Parallel M&A Clamp is suitable for the non-load-bearing splicing and branching of aluminum stranded wires and steel core aluminum stranded wires.
Contact Now
PAL1000 aluminum alloy optical cable insulation strain clamp is a product suitable for overhead insulated conductors. The product is used for cable pull, aluminum alloy body material, PA66 insulation core, stainless steel wire rope, and the product process is die-casting. The high-quality aluminum alloy material has strong corrosion resistance and is not easy to rust and age. The appearance is neat and tidy, and the unique design can well protect the cable.Features:1. Material: high strength aluminum alloy.
Contact Now