The energy distribution top tie can be used to fix naked or insulated wires inside the top grooves of pin insulators and submit insulators of the power distribution device.
Contact Now
The plastic fisher screw wall plug is made of high-quality PE material, which has strong fixation and is not easy to rotate. A variety of sizes are available for a wide range of applications. Corrosion-resistant, high-density polyethylene has rigidity, hardness and mechanical strength.
Contact Now
The power distribution cable tie is equipped with rubber pads to provide anti-wear function. The state line is not equipped with rubber pads and is not sandblasted. Since there are rubber pads to provide buffering around the wire, the abrasion of the contact surface between the wire and the insulator is avoided. Therefore, the power distribution cable can provide better protection to the wires, and the installation is easier and faster.
Contact Now
The top tie are all designed in a spiral structure and include aluminum-clad steel wires. the central part of the energy distribution cable is fashioned in the factory, and its form may be matched with diverse insulators and wires.
Contact Now
The power distribution top tie can be used to fix bare or insulated wires in the top grooves of pin insulators and post insulators of the power distribution system.
Contact Now
The strength distribution cable is equipped with rubber pads to offer anti-put on characteristic. the state line is not geared up with rubber pads and isn't sandblasted. due to the fact that there are rubber pads to provide buffering around the cord, the abrasion of the touch floor between the wire and the insulator is prevented. therefore, the energy distribution cable can provide better safety to the wires, and the installation is less difficult and faster.
Contact Now
1.Polymer Insulator Character:1.1high mechanical strength;1.2Good performance of hydrophobicity and anti-pollution;1.3 Excellent electrical Performance;1.4 small volume and lightweight. Type of productsOur products cover 10KV-1100KV high-voltage and extra-high voltage hollow ceramic insulators.Which include GIS outlet line insulator shellSF6 circuit breaker insulator shellCombined current and potential transformer insulator shell.capacitor insulator shellcable terminal insulator shellarrester insulator shell and solid pillar insulatorfuse protector insulatortank capacitor outlet line casi
Contact Now
The preformed top tie are all designed in a spiral structure and consist of two aluminum-clad steel wires. The central part of the power distribution cable is formed in the factory, and its shape can be matched with various insulators and wires.
Contact Now
The cable tie is able to loop and lock fully. Extra tie material left past the lock to prevent pull through. Self-locking design for fast and secure installation provided.The cable tie have maximum diameter capable of bundling two to four service wires and cables with cross-section in the range of 4-25mm2.
Contact Now
The tie strap is used for tying 11kV or 33kV cross-arms to poles. There are steel galvanized bolts and nuts assembled. All ferrous part is made in hot dip galvanized.
Contact Now
The S drop cable clamp is made of stainless steel rope and flame-retardant ABS plastic body, one head with a round steel wire, used to bind the self-supporting drop cable suspension wire, and hang the optical cable on the supporting device.Dimension:135×23.5×17.5mm(L×W×H).Instruction: Wrap the 2-6mm optical brazing wire in the cylindrical groove of the S part, and fix the optical brazing wire connecting rod.Packing: plastic bag first then come in a resistant biodegradable cardboard box with the customer information in the visible part of the box. Installation image:
Contact Now
1.Product name: tooth-shaped stainless steel cable tie buckle 2.Material: 316/304 stainless steel, with good and corrosion resistance.
Contact Now
1.The short span ADSS helical guy grip is used for 10.6-11.6mm ADSS cable, with approximate length 940mm±30mm, or customize based on requirements of customers.2.The structure of the short span ADSS guy grip is simple installation, with strong grip once the tubular structure naturally wound on the ADSS cable. 3.The short span ADSS helical guy grip has reliable performance, made of aluminum-clad steel.Using tips1.Due to the special structure of guy grip, only be used once after being stressed, and cannot be reused. 2.The specification and model of the guy grip must be provided when an
Contact Now
The preformed helical guy grip clamp for the conductor is hooked up to the tower by means of its matching fittings, along with insert ring, bowl-head striking plate, and so forth., that could replace conventional bolt-type tension clamps, compression-type anxiety clamps and wedge-type anxiety cables folder.Structure composition and material description 1. Non-twisted ring: standard form, suitable for small diameter wires; Stranded ring: suitable for larger diameter wires 2. Color code: starting mark of installation 3. Label: Indicate the product model 4. Pre-twisted wi
Contact Now
Helical tension set ADSS long span with D shackle, Thimble clevis, helical dead end, protector rods. A dead-end is installed at each end of the cable length to attach to the structures. Two dead ends are used at angle changes of 30 degree or greater, either horizontal or vertical.
Contact Now
Preformed helical guy grip clamp with long span helical dead end, thimble clevis, U shackle, link fitting and pole attachment with related accessories.
Contact Now
Steel belt 20X0.7mm with buckle, tts strength and ductility meet requirements for bending the different size of cables on poles. Steel Buckle can hold a single or double wrapped band configuration.Packing:Steel roll of 50 m is packed in form of closed reel rewind tape in nylon plastic roll.
Contact Now
Tension insulators are used for transmission and distribution lines and communication lines, broadcast line terminals, corners or large-span poles, The balance pole is subjected to tensile stress. When in use, the wire and the pull wire pass through the hole and slot, and the tension wire is used for insulation and connection.Features:1. Material: high strength carbon steel2. Application: for stay rod assembly3. Dimension: M16×1830mm4. Finish: hot dip galvanized
Contact Now
The socket clevis W-7A is the connection fitting in the power fittings. In the transmission line, the Wantou Hanging Board W-7A plays the role of suspending the insulator string and the suspension clamp, and bears greater working stress. Its safety performance is very important to the transmission line. The Wantou Hanging Board is in the construction of the power grid.
Contact Now
The adaptor socket clevis W-7B is mainly used to connect the suspension clamp and the insulator string, and cooperate with other accessories to connect the wires and insulate. ALL WELL W-7B has high mechanical strength, is not easy to produce cracks, has good structural stability, the product is not easy to age, and the surface is polished and polished without burrs. In the transmission line, the bowl head hanging board W-7B plays the role of hanging the insulator string and the suspension clamp, and bears greater working stress.
Contact Now
ADSS terminating helix dead end is made of aluminum-clad steel wire, and the pre-twisted wire is preformed into a bundle during processing, and a firm layer of emery is glued to the inner wall to increase the grip of the tension clamp under the condition of reducing the side pressure on the optical cable.
Contact Now
Features 1. There is a large contact area between the clamp and the wire, the stress distribution is even, there is no stress concentration point, and the achievable grip strength is not less than 95% of the stranded wire to calculate the breaking force.2. The wire clamp is made of the same material as the wire.3. The wire clamp is simple to install, does not require any complicated tools, and can be completed by one person.
Contact Now
The structure of the preformed strain clamp is simple, and its pre-twisted wire legs are twisted to form an empty tube, and the rear part is a pre-formed twisted ring. The empty tube formed by the legs of the pre-twisted wire can generate a strong grip when it is wound on the wire, and the twisted loop is used to fix the insulator.
Contact Now
The hoop device is composed of a hoop plate, a wing plate, a tie rib plate, a bolt and an inner liner. An embedded hoop, which is formed by joining the left and right halves of the hoop.
Contact Now